Estimated Lead Time : Usually ships in 1-10 working days.
Foxboro ( by Schneider Electric )
Product No : FCP270 P0917YZ
Product Type : Field Control Processor 270 (FCP270)
Memory Size : 16 MB SDRAM 32 MB flash memory
Input Voltage (Redundant Voltage) : 24 V dc typical
Consumption (Per Non-fault-tolerant Module) : 8.5 W, maximum
Operating Temperature : 0 to +60°C (+32 to +140°F)
Configuration : Single Processor Module. The fault-tolerant version consists of two processor modules, with an interconnecting fault-tolerant connector integral to the baseplate.
Dimensions (L x W x H) : 14.7cm x 5.15cm x 11.4cm
Weight : 0.6 Kg
Shipping Weight: 1.5 Kg
The FCP270 flattens and simplifies the I/A Series architecture. The I/A Series architecture only requires field enclosures plus workstations and Ethernet switches. For more information on The MESH control network architecture, refer to PSS 21H-7C2 B3.
The field-mounted FCP270 is an integral part of the highly-distributed control network where controllers are closely aligned to specific process units mounted in close proximity to their I/O and the actual equipment being controlled. Coordination between process units takes place via a fiber optic 100 Mbps Ethernet network.
The FCP270 is packaged in a rugged, die cast aluminum housing that does not require venting due to its efficient design. The FCP270 is CE certified, and it can be mounted without expensive special cabinets to prevent electronic emissions. The FCP270 can be mounted in Class G3 harsh environments.
ENHANCED RELIABILITY (FAULTTOLERANCE)
The unique and patented fault-tolerant operation of the FCP270 greatly improves reliability relative to other process controllers. The fault-tolerant version of the FCP270 consists of two modules operating in parallel, with two Ethernet connections to The MESH control network. The two FCP270 modules, married together as a fault-tolerant pair, provide continuous operation of the controller in the event of virtually any hardware failure occurring within one module of the pair.
Both modules receive and process information simultaneously, and faults are detected by the modules themselves. One of the significant methods of fault detection is comparison of communication messages at the module external interfaces.
Messages only leave the controller when both controllers agree on the message being sent (bit for bit match). Upon detection of a fault, self-diagnostics are run by both modules to determine which module is defective. The non-defective module then assumes control without affecting normal system operations.
This fault-tolerant solution has the following major advantages over controllers that are merely redundant: No bad messages are sent to the field or to applications using controller data because no message is allowed out of the controller unless both modules match bit for bit on the message being sent.
The secondary controller is synchronized with the primary one, which ensures up to the moment data in the event of a primary controller failure.
The secondary controller will have latent flaws detected prior to any switchover because it is performing exactly the same operations as the primary controller.
SPLITTER/COMBINER
Fault-tolerant FCP270 modules connect to a pair of fiber optic splitter/combiners (see Figure 1) that connect to Ethernet switches in The MESH. For each module, the splitter/combiner pair provides separate transmit/receive fiber connections for Ethernet switch 1 and 2. Fiber cables are connected so that the splitter/combiners pass inbound traffic from either switch to both modules, and pass outbound traffic from the primary module to either switch.
The splitter/combiner pair mounts in an assembly that fastens to the baseplate. The splitter/combiner is a passive device that uses no electrical power.
ENHANCED COMMUNICATIONS
The I/A Series architecture uses The MESH control network with 100 Mbps data communications between the FCP270s and the Ethernet switches
3 COMPONENTS AND ACCESSORIES
Product part numbers and their descriptions are listed below.
Part Number Description
MTL831C Analog Transmitter
MTL838C Receiver
MTL5553/MTL5053 Isolator/Power Supply
A standard USB Type C cable (not supplied by Eaton) is required to configure
the MTL838C
4 MECHANICAL INSTALLATION
4.1 Location
The MTL831C can be installed in either safe or hazardous areas (including Zone 0)
depending upon the requirements of the application.
4.2 Mounting options
The unit can be mounted on T-section DIN-rail. Eaton has a range of enclosures
– ENC8, ENC8-SS, ENC83 or ENC83-SS – to provide suitable IP67 protection if the
transmitter is located in an exposed area.
4.2.1 Mounting on T-section DIN-rail
To install, tilt the MTL831C to the left and hook to the left side of the standard 35mm
DIN46277 T-section rail. Push to the right and allow the unit to rotate down to sit flat
on the DIN Rail. Allow it to spring back to the left and the right side will hook to the
DIN Rail.
To remove, push the MTL831C to the right and tilt the right side away from the DIN
Rail. While tilted, allow it to spring back to the left and remove from the DIN Rail.
1 Remove
Install
Push 2
4 INM MTL831C Rev 1
DRAFT – 21 December 2018
5 CONNECTIONS
The connection terminals are along the edges of the Analog Transmitter. These are
divided into input sensor terminals (1 to 16), the Address terminals (A, S), and the
data highway terminals (+, S, -), as shown below.
5.1 Address
Leaving these two pins (A, S) open, sets the address of the MTL831C to “1”. A
jumper on these two pins sets the address to “2”. Either is valid for a system
with only one MTL831C connected to the MTL838C. When two MTL831Cs are
connected to a single MTL838C, they must be addressed uniquely. If they are on the
same address, only one will communicate with the MTL838C. The address affects
where the data is seen in the PC Software and what is available on the RS485 ports:
ADDRESS PC Software Modbus Port A or B LLMUX Emulation
1 MTL831C #1 tab Channels 1-16 Link 1, channels 1-16
2 MTL831C #2 tab Channels 17-32 Link 2, channels 1-16
Company’ s Name: Xiamen xiongba e-commerce Co., Ltd
Contact: Zoe
Phone Number/Wechat: +86-15359298206
Whatsapp : +86 15359298206
Q Q:2851759107
E-mail: 2851759107@qq.com
Spare parts spare parts, the main DCS control system of PLC system and the robot system spare parts,
Brand advantage: Allen Bradley, BentlyNevada, ABB, Emerson Ovation, Honeywell DCS, Rockwell ICS Triplex, FOXBORO, Schneider PLC, GE Fanuc, Motorola, HIMA, TRICONEX, Prosoft etc. Various kinds of imported industrial parts
Brand:ABB
Type：PFTL101B 2.0KN
Colour: new/usedWarranty: 365 days
Shipping method: Courier delivery
Main Products.
1、 ABB AC800M series modules, industrial robot parts DSQCseries, Bailey INFI 90, 800xA,
Advant OCS with Master Software, with MOD 300software Advant OCS, Freelance –
Process Industrial Distributed Control System, Symphony Melody, Satt OCS, Symphony DCI System Six,
Harmony/ INFI 90, Safety Systems
2、Schneider 140 series CPU modules
3、General electric (General Electric) series IC693 、IC695、 IC697、 IC698
Relay protection SR469 、 SR369 、 SR489 、SR750
IS200/IS215/IS220/IS420/DS200/DS215/VMIVME beginning with 7750 7807
4、Ticonex (Invensys) series 3721,3503,4351B,3625,3009
5、Bently (Bentley) 3500 series big card small card 1900 series power module
3500/15 3500/20 3500/22M 3500/42M 3500/25 3500/32 3500/53
6、Allen-Bradley (American AB) series products 1394 、 2711 、1756、1747 etc.
7、EMERSON /Westinghouse (Emerson Westinghouse) series products OVATION system、WDPF system、MAX0 system spare parts.
DELTAV Deltave VE3008/CE3008/SE3008/VE3007/VE3006 SE4006P2
8、Foxboro (Foxboro): I/A Series system、 FBM (Field Input/Output Module) sequence control、ladder logic control
Incident memo processing, digital-to-analog conversion, input/output signal processing, data communication and processing, etc. FCP270/FCP280/FBM201…FBM242
9、Woodword 9907-167、9907-164、9907-165、5464-414、5466-316、5501-467、5501-beginning 8444-beginning
10、Bosch Rexroth(Bosch Rexroth): Indramat,I/O module,PLC controller,drive module,etc.
11、Motorola (Moto): MVME 162, MVME 167, MVME5500, MVME6100 and other series.
FAQ:
1.Are your product brand-new and original?
Yes,100% brand-new and original products.
2.How long is the quality guarantee for your products?
All our products with 1 year warranty.
3.When will you delivery the goods?
With stock, we will arrange delivery in about 3 to 5 days; without stock, it will take relatively long time, but it won’t be too long, it mainly depends on order quantity.
4.What are your terms of payment?
Generally through TT, western union and PayPal.
