ABB XVC769AE101 3BHE006373R0101 module digital low-voltage power distribution system
Brand ABB Color Standard Application Industrial height 245mm rated current 469mA
Protection Level IP45 Suitable for motor power 156KW Application Site Power Industry BOM Number GJR2391500R1220 Power industry HIEE401782R0001 Part number 3BHE006373R0101 XVC769AE101
Applicable pipe 2 Whether imported is weighing 7.18 kg can be sold nationwide
ABB XVC769AE101 3BHE006373R0101 module digital low-voltage power distribution system
ABB Industrial module SYN5202-0277 3BHB006715R0277 5SHY3545L0014 ACU-01B 3HNA024871-001 5SHY3545L0009 3BHB013085R0001 3BHE009681R0101 When the rated speed is selected by closing the ldle/ rated switch contact, the fuel limit is set to the maximum fuel limit setting point or torque limit for the current engine operating speed, whichever is smaller. The speed reference selected at this point is determined by the state in which the remote switch is enabled. If the remote reference is not selected (the remote reference switch contact is on), the speed reference will rise from low idle to rated speed based on the accepted time set point. Closing the “raise” or “lower” contact (or “remote” contact) when rising from idle to the rated value immediately cancels the ramp from idle to the rated value. Raise/lower the ramp rate will take over, depending on whether you choose to raise or lower. Raise and lower commands are based on raise and lower rate setpoints for ramp engine RPM. The upper and lower limits determine the limits of these commands. If Enable Remote is selected (and Rated Speed is selected), GVC750BE101 VMIVME-7740-840 350-07740-840-M XVC769AE101 3BHE006373R0101 UFC760BE143 3BHE004573R0143 ABB Industrial module SYN5202-0277 The 3BHB006715R0277 5SHY3545L0014 ACU-01B 3HNA024871-001 controller will raise the speed to a reference value set by the remote speed setting MA input (in terms of rise or fall rate). Remote speed Settings operate in the 4 to 20 mA range. The values of the 4 mA and 20 mA remote reference setpoints must be set between the rise and fall limit setpoints. The 4 MA remote reference set point can be set to a speed below or above the 20mA set point, providing direct or reverse remote speed Settings. If remote is selected when the ldle/ rated switch contact is closed or during idle to rated ramp, the speed reference slopes up to a speed reference value determined by the milliamps on the remote speed setting input, based on the rise/fall rate setting point. Remote speed setting inputs between 2 and 4 mA are considered a minimum of 4 mA. Below 2 mA, remote input is considered to have failed. Between 4 and 20 mA, the controller determines the desired speed reference based on the straight line interpolated between the 4 mA remote reference and 20 mA remote reference set points. If a difference is detected between the current speed baseline and the remote baseline calculated from the mA input, the current speed baseline will be increased or decreased at a rate determined by “Increase or Decrease rate” so that the speed baseline is consistent with the remote speed baseline The Remote reference will not increase the speed beyond the “lift limit” or decrease below the “lower limit”. Nor does it change at a rate higher or lower than “lift rate”/” drop rate “, respectively. When a remote reference is selected and the remote input fails (less than 2mA), the speed reference remains at the current value. In this case, the speed reference can only be changed by increasing the remote reference above 2 mah, either turning on the remote enable switch and toggle the run/stop switch, or cycling power to the control (cycling power is not recommended). When the current operating mode is rated time, switching to idle will cause the engine speed to rise to idle based on the deceleration time set point.
ABB XVC769AE101 3BHE006373R0101 module digital low-voltage power distribution system
ABB UNS0119A-P V101
ABB UNS0874A
ABB UNS2980c-ZV4
ABB V4550220-0100
ABB 504994880
ABB 0745648E
ABB 0745745Q
ABB 07AC91D
ABB 07BR61R1 GJV3074376R1
ABB 07CR41
ABB 07DC91C
ABB 07EA90-SI
ABB 07KR51 220VDC
ABB 086339-001
ABB 086349-002
ABB 086406-002
ABB 086407-502
ABB 128877-103
ABB 1TGB302003R0003
ABB 1TGE120011R1001
ABB 216AB61
ABB 216DB61
ABB 216DB61 HESG324063R100/J
ABB 216EA61b
ABB 216EA62 1MRB150083R1/F 1MRB178066R1/F
ABB 216GD61A HESG324436R3/A HESG324428
ABB 3ASC25H203
ABB 3ASC25H204
ABB 3ASC25H209
ABB 3BHB003688R0001
ABB 3BHE027632R0101
ABB 3HAC025562-001/06
ABB 3HNA023093-001
ABB 408368B IAM MODULE
ABB 560CMU05
ABB 5SGX1060H0003
ABB 5SGX10H6004
ABB 5SGY3545L0020
ABB 5SGY35L4510
ABB 5SHX0660F0001
ABB 5SHX08F4502
ABB 5SHX1445H0002
ABB 5SHX1960L0004
ABB 5SHX2645L0004
ABB 5SHY3545L0009
ABB 5SHY35L4512
ABB 5SHY35L4520 5SXE10-0181 AC10272001R0101
ABB 5SHY4045L0006 3BHB030310R0001
ABB 5SHY5045L0020
ABB 6231BP10910
ABB 72395-4-0399123
ABB 751010R0815
ABB 81EU01E-E
ABB 83SR04C-E
ABB 83SR06B-E
ABB AB91-1 HESG437479R1 HESG437899
